|
|
| (One intermediate revision by the same user not shown) |
| Line 1: |
Line 1: |
| __NOTOC__
| | #REDIRECT [[Wireless_Africa_Home_Page]] |
| {| cellpadding="0px" cellspacing="0px" border="0px" width="100%"
| |
| |-
| |
| |align="left" width="100%" style="background-color:#5A1C10; border:0px solid #808080"| [[Image:tobar.jpg]]
| |
| |}
| |
| ----
| |
| {| cellpadding="10px" cellspacing="0px" border="0px" width="100%"
| |
| |-
| |
| |align="left" width="100%" style="background-color:#B3E8FF; border:1px solid #808080"|'''The Wireless Africa group is researching ways and means to develop sustainable information and communications technology in developing countries. This will be achieved through community-owned decentralized mesh networks built on open source technology'''
| |
| |}
| |
| | |
| | |
| == 10 December 2006 Prototype 1 of fully self-contained solar powered SA mesh node ==
| |
| | |
| [[Image: Sa-mesh-node2.JPG|thumb]]
| |
| | |
| The first prototype of a multi antenna self-contained mesh node was unveiled in December 2006. This nodes operates on a 45W solar panel to power the embedded computer and three 802.11 radios. The backhaul mesh is built in the 5GHz band using 2 radios which can be switched through a matrix of 4 antennas. This allows a full duplex connection on the backhaul. The Switachable antenna matrix consists of 4 5GHz panel antennas placed at 90 degrees to each other within a weather proof cylinder. An intelligent switching algorithm is used to switch through the four antennas and locate the other mesh nodes in the network. Switching happens as soon as traffic needs to be routed between mesh nodes. A 2.4GHz band radio connected to an omni is used to connect clients to the mesh node.
| |
| | |
| [[More Information on the SA mesh node]]
| |
| | |
| == 1 October 2006 Tin can connects rural home to outside world ==
| |
| | |
| The Meraka Institute's first Cantenna installed in a rural setting was successfully mounted onto the house of Agnes Mdluli, a health worker from Peebles valley, near White River in Mpumalanga. This can-antenna is made from a metal can, such as a coffee tin, and a section of bicycle spoke soldered into a special connector which can connect to another point with a similar antenna up to 5km away. The project in Peebles Valley is one of 10 sub-projects in the First Mile First Inch (FMFI) project being funded by the International Development Research Centre (IDRC).
| |
| | |
| These small, self-constructed antennas, which are made from locally available material, are connected to a low-cost WiFi card plugged into a computer. A small wireless router is placed in a weatherproof casing on a pole to which several community members could connect and form a community mesh network. This mesh networking technology allows the wireless installations to automatically configure themselves to find the optimal routes through the network and very little configuration is needed to set them up.
| |
| | |
| More information can be found here:
| |
| [[Mpumulanga Mesh]]
| |
| | |
| | |
| [[Image: Cantenna-peebles-small.jpg|thumb]]
| |
| | |
| | |
| | |
| | |
| | |
| | |
| ----
| |
| | |
| [[NEW: Quick getting started guide for setting up an outdoor mesh node]]
| |
| | |
| | |
| Please use the discussion tag above to comment and provide suggestions!
| |
| Please Email wa-admin(at)meraka.org.za if you wish to contribute or for further information.
| |
| | |
| [[Image: Meraka.jpg]] | |